TryBuildCalcLumber Calculator(Quantity, Board Feet & Cost)
Use this lumber calculator to estimate quantity, board feet, and cost for a construction or framing project.
Find out how many pieces to order and how much board footage that comes to, using actual dressed size rather than the nominal size name.
Calculate lumber quantity and cost.
🕒 Last updated: August 25, 2026
Inputs
ℹ️Actual dressed size is always used for volume and weight. Board foot billing basis is set separately below.
ℹ️Most suppliers bill board feet using nominal size, which gives a higher figure than the physically dressed board. Confirm which your supplier uses before ordering.
Quantity
Cost Settings
Pieces Needed (Including 5% Wastage): 16 pieces
Size: 2x6 (1½ x 5½ in / 38 x 140 mm actual)
Piece Length: 3.05 m (10.00 ft)
Total Linear Length: 48.77 m (160.00 ft)
Total Volume: 160.00 board ft
Board Feet per Piece (nominal basis): 10.00 bf
Total Volume (actual dimensions): 0.260 m³ (9.17 cft)
Not sure your span/spacing combination is actually adequate? Beam Load Calculator →
Using this timber for roof purlins? Roofing Sheet Calculator →
Timber / Lumber Layout Visualization
Lumber quantity and cost estimate
This page is pre-filled with a 2x6, 10 ft piece at quantity 15, a common size for joists or heavier framing.
The calculator inputs are pre-filled for this use case so the result card starts with values that match the page topic. You can adjust any input to recalculate the estimate.
- Default: 2x6, 10 ft, 15 pieces.
- Includes actual dressed dimensions automatically.
- Switch pricing basis between per piece and per board foot.
What Is a Timber / Lumber Calculator?
Lumber is sold under a nominal name — a "2x4" — but its actual dressed size after milling is smaller. Physical volume and weight should use the actual dressed size, while board-foot billing is commonly quoted from the nominal trade size unless your supplier prices from actual dimensions. This calculator converts piece size, length, and either a direct quantity or a run length and on-center spacing into the number of pieces to order, total board feet, metric volume, and cost.
It works for wall studs, floor and roof joists, roof purlins, and formwork/shuttering timber alike — any application built from repeated same-size pieces. Enter a standard nominal size or a fully custom actual dimension, then choose whether standard-size board feet should follow nominal trade billing or actual dressed-size billing.
What makes this calculator different:
Most online lumber calculators ask for a single volume figure or work only in board feet, U.S. nominal sizes, and imperial units. This one keeps the billing and physical dimensions separate, supports both a direct piece-count entry and a run-length-plus-spacing calculation using the standard "run ÷ spacing, rounded up, plus one" framing convention, and reports results in board feet and metric volume together — so it works equally well for a U.S. framing takeoff and a metric-region purlin or joist order.
Timber / lumber calculation formula
Step 1 - Piece Count
By Piece Count: entered directly
By Run Length & Spacing: Pieces = ceil(Run Length / Spacing) + 1
Step 2 - Wastage-Adjusted Total
Step 3 - Board Feet and Volume
Board Feet per Piece = (Billing Thickness in x Billing Width in x Length ft) / 12
Billing dimensions = Nominal size (e.g. 2x4 = 2 x 4 in) by default, or Actual dressed size if selected
Total Board Feet = Board Feet per Piece x Total Pieces
Total Volume (m³) = Actual Thickness m x Actual Width m x Length m x Total Pieces (always actual, regardless of billing basis)
US softwood dimension lumber is traditionally billed by nominal size (Product Standard PS 20) even though the physically delivered board is smaller — a nominal 2x4 x 8 ft bills as 5.33 board feet, not the 3.5 board feet its actual 1½ x 3½ in cross-section would give. This calculator defaults to nominal billing to match most supplier invoices, with actual dimensions available as an option. Metric volume always uses actual dimensions either way, since that reflects the true physical material.
Step 4 - Cost
Example timber/lumber calculation
This example uses the active calculator inputs above and follows the same four steps from the formula section. Each table shows the value used, the formula applied, and the result produced.
Input Values Used
| Input | Value |
|---|---|
| Size | 2x6 (1½ x 5½ in / 38 x 140 mm actual) |
| Piece length | 10 ft |
| Quantity (entered directly) | 15 |
| Wastage | 5% |
| Board foot billing basis | Nominal (standard trade billing) |
Step 1 - Piece count
| Item | Formula | Result |
|---|---|---|
| Theoretical pieces | Entered directly | 15 |
Step 2 - Wastage-adjusted total
| Item | Formula | Result |
|---|---|---|
| Total pieces to order | ceil(15 x (1 + 5%)) | 16 |
Step 3 - Board feet and volume
| Item | Formula | Result |
|---|---|---|
| Board feet per piece (nominal basis) | (2 x 6 x 10) / 12 | 10 bf |
| Total board feet | 10 x 16 | 160 bf |
| Total volume | 38.1 mm x 139.7 mm x 3.05 m x 16 | 0.26 m³ (9.17 cft) |
Step 4 - Cost
| Item | Formula | Result |
|---|---|---|
| Cost estimation not enabled | ||
Therefore, this order needs 16 pieces of 2x6 (1½ x 5½ in / 38 x 140 mm actual), totaling 160 board feet (0.26 m³).
Limitations
- This calculator does not verify structural adequacy — actual allowable span depends on species, grade, size, spacing, and load together, and must be confirmed against a published span table or engineer's design.
- It does not account for extra pieces needed for openings, corners, headers, or intersecting framing — a spacing-based count assumes a simple, uninterrupted run.
- Standard nominal-to-actual size conversions are general North American S4S conventions — confirm exact actual dimensions with your specific supplier, particularly outside North America.
- It does not calculate fastener quantity, connector hardware, or treatment/species pricing differences — these should be estimated separately.
- It does not account for multiple distinct piece sizes in one calculation — run the calculator separately for each size used in your project.
Related Calculators
Disclaimer: This calculator provides approximate results for planning and estimation purposes only. Actual requirements may vary based on site conditions, materials, workmanship, and local building regulations. Always consult a qualified engineer, architect, or construction professional before making final decisions.