TryBuildCalcRidge Vent Calculator (Exhaust Vent Linear Footage)
Size your ridge vent instantly.
🕒 Last updated: September 12, 2026
Inputs
ℹ️Total floor area of the attic space, not the home's conditioned square footage.
ℹ️IECC climate zone — determines whether a vapor retarder is one of the conditions for the reduced 1:300 ratio (only required in Zones 6-8).
ℹ️Required for the reduced 1:300 ratio in every zone: 40-50% of NFA from vents within 3 ft of the ridge/highest point, with the rest in the bottom third of the attic. This is a physical siting condition this calculator can't verify for you — confirm it matches your actual (or planned) vent layout.
ℹ️Net Free Area per linear foot, stamped on your continuous soffit vent product — 9 sq in/ft is a common default, but check your actual product.
ℹ️Ridge vents are sized continuously by linear foot; gable/box/turbine vents are sized individually by unit count.
ℹ️Net Free Area per linear foot, stamped on your ridge vent product — 18 sq in/ft is a commonly-cited default, but check your actual product.
Soffit (Intake) Vent Needed
64 ft
Total continuous linear feet, split across all eaves
Ridge (Exhaust) Vent Needed
21.4 ft
Continuous ridge vent length
Attic & Ratio
Attic floor area: 2,000 sq ft
Climate zone: Zone 6 — Cold (Upper Midwest, New England, MT)
Class I/II vapor retarder: Yes
Vent placement confirmed: Yes
Ratio applied: 1:300 (exception met)
Required NFA
Total required: 960 sq in
Intake (60%): 576 sq in
Exhaust (40%): 384 sq in
Vent Sizing
Soffit NFA rate: 9 sq in/ft
Ridge NFA rate: 18 sq in/ft
Assumptions Used
Per IRC R806.2, total required Net Free Area (NFA) is your attic floor area ÷ 150 (the general rule) or ÷ 300 (the exception) — × 144 to convert sq ft to sq in. The 1:300 exception requires BOTH: (1) in Climate Zones 6, 7, and 8 ONLY, a Class I or II vapor retarder installed on the ceiling's warm side (outside those zones, the code doesn't condition the exception on a vapor retarder at all); and (2) 40-50% of the required NFA sited within 3 ft of the ridge/highest point, with the balance in the bottom third of the attic — a physical placement condition you confirm above, since this calculator can't verify actual vent siting. If either applicable condition isn't met, the standard 1:150 ratio applies. That total is split 60% intake (soffits) / 40% exhaust — code minimum is a straight 50/50 split; this calculator defaults to the commonly-recommended 60/40 intake-heavy split instead (the 40% exhaust share also sits at the lower bound of the exception's required 40-50% upper-vent range). Soffit and ridge vent lengths are rounded UP to the next tenth of a foot, never down — these are minimum required lengths, so a displayed length must never fall short of the raw calculated requirement. Soffit linear feet = intake NFA ÷ your soffit vent's rated NFA per linear foot (9 sq in/ft is a typical continuous-vent rating, confirmed against a manufacturer spec sheet this session — but varies by product, so use your actual vent's rating). For a ridge vent, required length = exhaust NFA ÷ your ridge vent's rated NFA per linear foot (18 sq in/ft is a commonly-cited typical figure — again product-specific). For gable/box/turbine vents, vent count = exhaust NFA ÷ your vent's own rated NFA, rounded UP (a fraction of a vent isn't purchasable, and rounding down would under-ventilate). This is a planning estimate — always verify your chosen vent products' actual rated NFA (stamped on the product or its spec sheet) rather than relying on the defaults shown here, and confirm baffles keep insulation from blocking soffit airflow.
Looking for the verification checklist, reference tables, tips, or common mistakes?See the complete Attic Ventilation Calculator.
Ridge vent sizing
Ridge vent length is the exhaust NFA (40% of total required NFA) divided by the vent's rated NFA per linear foot, rounded UP to the next tenth of a foot since this is a minimum requirement — a continuous, linear-footage calculation, unlike gable or box vents which are sized by unit count.
This page defaults to a larger 2,000 sq ft attic in cold Climate Zone 6, WITH a Class I/II vapor retarder installed and vent placement confirmed — meeting both conditions IRC R806.2's exception requires in Zone 6 — demonstrating the relaxed 1:300 ratio.
Attic Ventilation Calculator Formula: How Is It Determined?
Total required Net Free Area (NFA) is determined by attic floor area and the applicable ratio, then split between intake and exhaust, then converted into either continuous vent length (soffit/ridge) or individual vent count (gable/box/turbine).
Step 1 — 1:300 Exception Eligibility
Zone needs vapor retarder = Climate Zone is 6, 7, or 8
Qualifies for 1:300 = Vent Placement Confirmed AND (Zone does NOT need vapor retarder OR Vapor Retarder Installed)
Ratio = 1:300 if qualifies, else 1:150 (IRC R806.2 general rule)
IRC R806.2's 1:300 exception requires BOTH conditions: in Climate Zones 6, 7, and 8 ONLY, a Class I or II vapor retarder on the ceiling's warm side (outside those zones the code doesn't condition the exception on a vapor retarder at all); and, in every zone, 40-50% of NFA sited within 3 ft of the ridge/highest point with the balance in the bottom third of the attic — a physical placement condition you confirm directly, since this calculator can't verify actual vent siting.
Step 2 — Required NFA
Required NFA (sq in) = (Attic Area sq ft / Ratio) x 144
The applicable ratio from Step 1 converts attic floor area into the total Net Free Area required, in square inches.
Step 3 — Intake / Exhaust Split
Intake (Soffit) NFA = Required NFA x 60%
Exhaust NFA = Required NFA x 40%
Code minimum is a straight 50/50 split. This calculator defaults to the commonly-recommended 60/40 intake-heavy split instead — the extra intake creates slight positive attic pressure, which reduces wind-driven rain/snow intrusion through a ridge vent. 40% exhaust also sits at the lower bound of the 1:300 exception's required 40-50% upper-vent range.
Step 4 — Vent Sizing
Soffit Linear Feet = ceil-to-tenth(Intake NFA / Soffit Vent NFA per Linear Foot)
Ridge Linear Feet = ceil-to-tenth(Exhaust NFA / Ridge Vent NFA per Linear Foot)
OR Vent Count = ceil(Exhaust NFA / NFA per Gable-Box-Turbine Vent)
Continuous vents (soffit, ridge) are sized by dividing the required NFA by the product's rated NFA per linear foot, rounded UP to the next tenth of a foot — these are minimum lengths, so rounding to-nearest could round a length below what's actually required. Individual vents (gable, box, turbine) are sized by dividing by the product's rated NFA per unit and rounding UP to a whole vent — a fractional vent isn't purchasable, and rounding down would under-ventilate.
Worked Example
This example walks through your current inputs above, using the same steps as the Formula section.
Input Values Used
| Input | Value |
|---|---|
| Attic floor area | 2,000 sq ft |
| Climate zone | Zone 6 — Cold (Upper Midwest, New England, MT) |
| Class I/II vapor retarder | Yes |
| Vent placement confirmed | Yes |
| Exhaust vent type | Ridge Vent (continuous) |
Step 1 — 1:300 Exception Eligibility
| Calculation | Result |
|---|---|
| Zone needs vapor retarder | Yes (Zone 6-8) |
| Qualifies for 1:300 | Yes |
| Ratio applied | 1:300 |
Step 2 — Required NFA
| Calculation | Result |
|---|---|
| Required NFA = (2,000 / 300) x 144 | 960 sq in |
Step 3 — Intake / Exhaust Split
| Calculation | Result |
|---|---|
| Intake (soffit) = 960 x 60% | 576 sq in |
| Exhaust = 960 x 40% | 384 sq in |
Step 4 — Vent Sizing
| Calculation | Result |
|---|---|
| Soffit vent = 576 / 9 sq in/ft | 64 ft |
| Ridge vent = 384 / 18 sq in/ft | 21.4 ft |
Therefore, a 2,000 sq ft attic needs approximately 64 ft of soffit vent and approximately 21.4 ft of ridge vent. Verify your chosen vent products' actual rated NFA before purchasing.
Related Calculators
Disclaimer: This calculator provides approximate results for planning and estimation purposes only. Actual requirements may vary based on site conditions, materials, workmanship, and local building regulations. Always consult a qualified engineer, architect, or construction professional before making final decisions.