TryBuildCalc

Siding Resources

Wood Siding Species Guide: Cedar vs Redwood vs Pine vs Engineered Wood

Choosing wood siding isn't just Lap vs Board & Batten style — the species (or whether you choose an engineered wood product instead of solid-sawn natural wood) drives most of the real differences in cost, decay resistance, and maintenance. This guide compares the common options directly.

Last updated: November 19, 2026

Picking wood siding usually gets framed as Lap vs. Board & Batten style, but the species — or whether you choose an engineered wood product instead of solid-sawn lumber at all — drives most of the real differences in decay resistance, cost, and how much upkeep you're signing up for.

This guide compares Western red cedar, redwood, pine, and engineered wood directly, with a worked cost example across all four for the same wall area.

Species Comparison

The table below compares the common wood siding options across the factors that matter most.

Species / ProductNatural Decay ResistanceTypical Cost TierMaintenanceBest Fit
Western Red CedarHigh — natural oils/extractivesPremiumModerate — restain every 3-5 yrs, or let weather to grayHumid/coastal climates, premium natural look
RedwoodHigh — natural tanninsPremium (often higher outside the West Coast)ModerateWest Coast projects, premium natural look
Pine / Fir (standard species)Low — needs paint/treatmentBudgetHigh — full paint film every 3-7 yrs, rot risk if neglectedBudget-conscious projects willing to maintain a paint film
Engineered Wood (LP SmartSide-style)High — factory zinc-borate treatmentMid-rangeLow to moderate — prefinished options reduce refinishingBest balance of authentic wood look and lower maintenance

Worked Cost Example

Example — Installed Cost for 1,200 Sq Ft of Wall Siding by Species

A home with 1,200 sq ft of net wall area is priced for each species/product at a representative mid-range installed rate.

Species / ProductFormula / SubstitutionResult
Pine (primed, standard grade)1,200 × 6.00$7,200
Engineered wood (LP SmartSide-style)1,200 × 7.50$9,000
Western red cedar (standard grade bevel siding)1,200 × 10.00$12,000
Redwood (standard grade, shipped outside West Coast)1,200 × 11.50$13,800

The spread between pine and redwood on this 1,200 sq ft example is roughly $6,600 upfront — but pine's much higher repainting frequency can close or even reverse that gap over a 20-25 year ownership horizon.

Common Mistakes

Using Standard (Non-Resistant) Species Without Treatment or Paint Protection

Pine, fir, and spruce lack cedar's and redwood's natural decay resistance — leaving one of these species unfinished or unpainted, or letting a paint film fail and go unrepaired, invites rot and insect damage far faster than the same situation would on cedar or redwood.

Assuming All 'Cedar' Siding Is the Same Quality

Cedar is graded, and clear (no-knot) grades cost meaningfully more than knotty grades for the same species — compare quotes at the same grade, not just the same species name.

Applying an Uneven Finish Across Sun-Exposed and Shaded Elevations

A clear finish or light stain fades at different rates depending on sun exposure, producing a blotchy, mismatched look between elevations over a few years — commit evenly to either natural graying or a maintained stain/paint schedule across the whole house, not a half-measure.

Using Standard Carbon-Steel Fasteners on Any Wood-Based Siding

This applies equally to natural wood and engineered wood siding — standard fasteners corrode and stain the siding over time. Use stainless steel or hot-dip-galvanized fasteners per USDA Forest Products Laboratory guidance and the specific manufacturer's instructions.

Skipping a Manufacturer's Required Cut-Edge Sealant on Engineered Wood

Many engineered wood siding products specify a field-applied sealant on any cut board end to maintain their decay-resistance warranty, since factory treatment doesn't fully penetrate a freshly cut edge — skipping this step on site-cut boards can void warranty coverage even though the board looks identical to an uncut one.

Standards and References

SourceWhat It Covers
Western Red Cedar Lumber Association (WRCLA)Bevel siding grading, dimensions, and installation guidance referenced throughout this guide.
California Redwood AssociationRedwood grading and siding installation guidance.
ICC-ES evaluation reports for engineered wood siding (e.g., LP SmartSide)Substrate warranty terms and factory treatment claims for engineered wood products.
USDA Forest Products LaboratoryFastener corrosion and compatibility guidance applicable to both natural and engineered wood siding.

Final Verdict

Choose cedar or redwood for the best natural decay resistance and premium appearance, pine if budget is the priority and you commit to a real paint-maintenance schedule, and engineered wood for the best balance of authentic wood texture and lower long-term maintenance.

  • Cedar and redwood both have genuine natural decay resistance from their own oils/tannins — pine and fir don't.
  • Pine siding needs a maintained paint film as its substitute protective barrier; skipping repainting invites rot much faster than on cedar or redwood.
  • Engineered wood closes most of the maintenance gap with fiber cement while keeping a wood-grain appearance.
  • Confirm cedar grade (clear vs. knotty) before comparing quotes — it's a major price and appearance variable within 'cedar' alone.
  • Commit evenly to either natural graying or a maintained finish across the whole house — a half-measure finish weathers unevenly.
  • Use stainless or hot-dip-galvanized fasteners on both natural and engineered wood siding, and seal any field-cut edges per the manufacturer's instructions.

Related calculators

Use these calculators when you need to turn this reference information into project quantities:

Related resources

  • Vinyl vs Fiber Cement vs Wood Siding: Which Is Best

    Head-to-head comparison of vinyl, fiber cement, and wood/engineered wood siding covering installed cost, lifespan, maintenance, weight, fire resistance, and DIY feasibility — with a scenario table and worked cost example.

  • Siding Lifespan and Maintenance Schedule Guide

    Expected lifespan and the routine maintenance schedule for every common siding material — vinyl, metal panel, fiber cement, wood, engineered wood, cedar shake/shingle, EIFS, stucco, and brick/stone veneer — in one reference table.

FAQ

Western red cedar contains natural oils and extractives (including compounds called thujaplicins) that give it genuine, built-in resistance to decay and insect damage without any chemical treatment — a real, documented property, not just marketing. It's also lightweight, dimensionally stable (resists cupping and warping better than many other softwoods), and ages to an attractive silver-gray patina if left unfinished. These combined properties are why it commands a premium price over standard construction-grade softwoods like pine.
Redwood shares cedar's natural decay resistance, derived from its own tannins rather than cedar's thujaplicins, and performs comparably well as a siding material. The main practical differences are availability and cost — redwood is primarily harvested and sold on the US West Coast, so shipping it to other regions typically adds meaningfully to its already-premium price, while cedar has somewhat broader availability across North America. Where both are locally available at similar cost, the choice comes down mostly to grain appearance and personal preference.