Siding/Cladding Removal & Disposal Calculator (Debris Weight, Dumpster Size & Cost)
Estimate debris weight, dumpster size, and disposal cost for tearing off old siding.
🕒 Last updated: November 19, 2026
Inputs
Section 1: Areas Being Removed
Add one row per wall section or area being torn off, with its material (changes removal weight and density).
Area 1
Section 2: Site & Dumpster Options
0.1 tons of debris from 300 sq ft
Recommended: 10 yd roll-off (comfortable fit on both measures)
Debris Weight & Volume
Total Debris Weight: 158 lb (71 kg)
Total Debris Weight: 0.08 US tons (0.07 tonnes)
Required Loose Volume: 0.8 cu yd (0.6 m³)
Dumpster Sizing
Recommended Dumpster Size: 10 yd
Sized By: Comfortable on both weight and volume
Fill at Recommended Size: 4% of weight limit, 8% of volume capacity
Quick Insight
Estimated from 300 sq ft of siding/cladding across 1 area(s): 0.1 ton(s) of debris, needing roughly 0.8 cubic yards of dumpster space — a 10 yd roll-off is recommended, comfortably within both its weight and volume limits.
Approximate results for planning only. Verify with a professional.
Dumpster Fill Estimate
What Is a Siding/Cladding Removal & Disposal Calculator?
If you're asking "what size dumpster do I need for this siding tear-off" or "how much will it cost to haul away this debris," this calculator answers both. Enter the area(s) of siding/cladding being removed, each with its material (and gauge or coursing where relevant), and it totals the debris weight, the loose volume that debris actually needs in a container, a recommended roll-off dumpster size, and an optional disposal cost estimate.
This calculator is scoped to the DEBRIS side of a re-siding job. For the new cladding going back on afterward, see this category's Vinyl Siding, Fiber Cement Lap Siding, and House WrapCalculators, or any of the other material-specific install calculators in the Siding & Exterior Cladding category.
What makes this calculator different:
Most online dumpster-size calculators size a container by volume alone, and most siding-specific tools only cover one material. This one checks BOTH a dumpster's rated cubic-yard volume AND its typical weight limit, computes each material's own debris weight AND its own debris density (siding spans roughly a 20-fold weight range across materials, from vinyl to stucco), and reports explicitly which constraint actually drove the recommended size — instead of hiding that behind one number, or assuming every material packs a dumpster the same way.
How the siding removal & disposal calculation works
Every area's material weight and debris density are resolved per row, totaled into a debris weight and a required dumpster volume, then checked against a standard dumpster catalog on BOTH its weight limit and its volume capacity.
Step 1 - Weight & density per area
Area (sq ft) x Material Weight (lb/sq ft) = Area Debris Weight (lb)
Area Debris Weight (lb) / Material Bulk Density (lb/yd^3) = Area Raw Volume (yd^3)
Each of the 10 supported materials carries its own weight-per-sq-ft AND its own debris bulk density — stucco and adhered brick/stone veneer are both heavy AND dense (rubble-like), while vinyl and EIFS foam are light AND bulky (lots of trapped air once broken up). Metal/Steel Panel resolves its weight from the selected gauge; Cedar Shingle/Shake doubles its weight when Double Coursing is selected.
Step 2 - Total debris weight
Total Weight = Sum of every area's Debris Weight x (1 + 5% hardware/residue allowance)
Total Weight (tons) = Total Weight (lb) / 2000
A small allowance is added on top of the bare material weight for fasteners, flashing offcuts, and residual sealant or furring that rides along with real removed siding debris — not estimated as separate line items, just folded into the total debris weight.
Step 3 - Required loose dumpster volume
Raw Volume = Sum of every area's own Raw Volume (yd^3)
Required Volume = Raw Volume x (1 + 10% fill safety margin)
Required volume is summed from EACH area's own material-specific raw volume, not from one global density applied to the pooled total weight — summing weight-divided-by-density per row before adding the fill margin keeps a mixed-material job (say, stucco on one wall and vinyl soffit elsewhere) accurate instead of averaging two very different materials together.
Step 4 - Dumpster size: check BOTH constraints
Smallest catalog size where (Size's yd^3 >= Required Volume) AND (Size's Weight Limit >= Total Weight)
Binding Constraint = whichever constraint alone needed the bigger size
Most online dumpster calculators size by volume alone. This checks a standard roll-off catalog (10, 15, 20, 30, 40 yd, each with a typical weight limit) against BOTH measures and reports which one actually drove the recommendation — dense materials like stucco or veneer typically bind on weight, while bulky light materials like vinyl or EIFS foam typically bind on volume.
Step 5 - Cost (optional)
Included Tons = Dumpsters Needed x Weight Included in Base Rate
Overage Tons = MAX(0, Total Weight (tons) - Included Tons)
Total Cost = (Dumpsters Needed x Base Rental Rate) + (Overage Tons x Overage Rate)
Real roll-off rental pricing bundles a weight allowance into one flat base price, then bills any extra tonnage separately at a per-ton overage rate — this models both pieces rather than one flat per-ton rate applied to the entire load.
Real-World Siding Removal Example
This example uses the active calculator inputs above and follows the same steps from the formula section.
Areas Used
| Area | Size | Material | Weight |
|---|---|---|---|
| Area 1 | 300 sq ft | Vinyl Siding | 150 lb |
Step 1 — Debris Weight & Volume
| Item | Result |
|---|---|
| Total Debris Weight | 158 lb (0.08 tons) |
| Required Loose Volume | 0.8 cu yd |
| Recommended Dumpster | 10 yd, sized by a comfortable fit on both measures |
Therefore, for this job you need an estimated 0.1 tons of debris removal, needing roughly 0.8 cu yd of dumpster space — a 10 yd roll-off, sized by a comfortable fit on both measures.
Essential Checklist+−
Complete these critical checks before approving the work or proceeding to the next construction stage.
✓Area & Material Assessment+-
- Every area being torn off was measured on site (not guessed) and entered as its own row, with the correct material for THAT area.
- Before any cutting or demolition starts, the area was checked for hidden wiring, plumbing, exterior outlets, or hose bibs behind the cladding.
- If the building was built or last re-sided before 1980, a sample was tested for lead paint and/or asbestos by a qualified lab BEFORE any disturbance, rather than assuming it's safe.
✓Lead Paint, Asbestos & Site Safety+-
- If lead paint or asbestos was confirmed or suspected, a licensed abatement/lead-safe contractor was engaged instead of DIY removal — this is a legal requirement (EPA RRP rule) in many US jurisdictions for pre-1978 buildings, not just a best practice.
- Exterior utilities, light fixtures, hose bibs, and dryer/bath vents penetrating the cladding were confirmed shut off, capped, or protected before cutting around them.
✓Dumpster Sizing & Disposal+-
- The recommended dumpster size's BINDING constraint (weight vs. volume) was understood — a stucco- or veneer-heavy job commonly hits the weight limit long before filling the container, while a vinyl or EIFS job often fills the container first.
- If a specific dumpster size was manually selected instead of the recommendation, its adequacy flag (fits / too small) was checked before booking it.
✓Cost & Final Check+-
- The total estimated weight (tons) was compared against the hauler's actual included weight allowance before committing to a base rental price.
Full QC Checklist+−
Verify area assessment, lead paint/asbestos safety, dumpster sizing, and cost before starting a re-siding tear-off job.
✓Area & Material Assessment+-
- Every area being torn off was measured on site (not guessed) and entered as its own row, with the correct material for THAT area.
- Before any cutting or demolition starts, the area was checked for hidden wiring, plumbing, exterior outlets, or hose bibs behind the cladding.
- If the building was built or last re-sided before 1980, a sample was tested for lead paint and/or asbestos by a qualified lab BEFORE any disturbance, rather than assuming it's safe.
- Metal/Steel Panel areas used the correct gauge (changes weight roughly 2x across the catalog range), not an assumed default.
- Cedar Shingle/Shake areas were correctly marked Double Course when a double-coursed assembly is actually installed, not assumed Single.
- Any house wrap, rigid insulation, furring strips, or sheathing being removed in the same job was accounted for separately — this calculator covers the cladding material debris only.
- Material type was confirmed against the actual siding being removed, not assumed from the building's age or region — two different claddings sometimes coexist on additions or re-sided sections.
✓Lead Paint, Asbestos & Site Safety+-
- If lead paint or asbestos was confirmed or suspected, a licensed abatement/lead-safe contractor was engaged instead of DIY removal — this is a legal requirement (EPA RRP rule) in many US jurisdictions for pre-1978 buildings, not just a best practice.
- Dust and paint-chip control (ground sheeting, containment, wetting debris) was planned before demolition starts, especially near soil, gardens, or occupied spaces.
- PPE (gloves, eye protection, a properly rated respirator) was confirmed available for every person doing the tear-off.
- Ladders, scaffolding, or lift equipment for upper-wall and gable areas were planned and inspected before work starts, not improvised on site.
- A clear path from the work area to the dumpster was planned, accounting for debris weight and trip count, not just distance.
- Exterior utilities, light fixtures, hose bibs, and dryer/bath vents penetrating the cladding were confirmed shut off, capped, or protected before cutting around them.
✓Dumpster Sizing & Disposal+-
- The recommended dumpster size's BINDING constraint (weight vs. volume) was understood — a stucco- or veneer-heavy job commonly hits the weight limit long before filling the container, while a vinyl or EIFS job often fills the container first.
- If a specific dumpster size was manually selected instead of the recommendation, its adequacy flag (fits / too small) was checked before booking it.
- The hauler's own posted weight limit and overage rate for the booked size were confirmed directly with them — the catalog figures here are typical planning figures, not one hauler's exact posted terms.
- For a job flagged as exceeding a single largest dumpster, multiple dumpsters (or a specialized heavy-debris hauler) were actually arranged, not just one oversized load.
- On a mixed-material job, the Debris Weight by Material breakdown was reviewed so the heaviest material (often what actually drives dumpster sizing) is clearly identified.
- Local rules on where a roll-off dumpster can be placed (driveway, street permit, HOA) were checked before delivery day.
✓Cost & Final Check+-
- The total estimated weight (tons) was compared against the hauler's actual included weight allowance before committing to a base rental price.
- Overage cost was budgeted for, not assumed away, on any job where the estimated weight is close to or above the included allowance.
- Demolition labor, dumpster delivery/pickup/trip fees, scaffolding/lift rental, and any permit cost were added on top of this calculator's totals — none of those are estimated here.
- The exposed sheathing/framing was inspected for rot, pest damage, or hidden moisture issues before new house wrap or cladding goes back on.
Reference Tables
Debris weight by material (removal basis)
| Material | Weight | Debris Density | Notes |
|---|---|---|---|
| Vinyl Siding | ~0.5 lb/sq ft | ~200 lb/yd³ | Lightest material; usually volume-bound, not weight-bound |
| Fiber Cement Lap Siding | 2.3 lb/sq ft | ~600 lb/yd³ | Same figure as this site's install calculator |
| Wood / Engineered Wood Siding | ~1.5 lb/sq ft | ~300 lb/yd³ | Lap/clapboard style, cedar or engineered wood |
| Stucco (3-Coat) | ~10 lb/sq ft | ~2,000 lb/yd³ | Heaviest common material; almost always weight-bound |
| Brick Veneer (Adhered Thin Brick) | 12 lb/sq ft | ~1,800 lb/yd³ | Adhered thin veneer only, not full-wythe brick |
| Manufactured Stone Veneer | 10 lb/sq ft | ~1,800 lb/yd³ | Includes setting mortar/scratch coat riding along |
| Metal/Steel Panel Siding | 0.72–1.41 lb/sq ft | ~150 lb/yd³ | By gauge: 29/26/24/22 — same table as this site's install calculator |
| Cedar Shingle Siding | 0.7 lb/sq ft (x2 if double-coursed) | ~300 lb/yd³ | CSSB's own published weight-per-square tables |
| Cedar Shake Siding | 1.3 lb/sq ft (x2 if double-coursed) | ~300 lb/yd³ | Heavier than shingles; same doubling for double coursing |
| EIFS (Synthetic Stucco) | ~2 lb/sq ft | ~200 lb/yd³ | Foam-core assembly; lowest-confidence figure, disclosed as an estimate |
Standard roll-off dumpster sizes
| Size | Typical Weight Limit | Best For |
|---|---|---|
| 10 yd | ~2 tons | A single wall section or small repair |
| 15 yd | ~3 tons | Several wall sections |
| 20 yd | ~4 tons | A full side of a house or mid-size job |
| 30 yd | ~5 tons | A whole house of light-to-mid-weight siding |
| 40 yd | ~6 tons | A full-house heavy material (stucco, veneer) tear-off |
Weight limits are typical mid-range figures cross-checked across multiple waste-hauling industry sources, not one hauler's exact posted terms — confirm the specific limit and overage rate with your rental company before ordering.
How to Use the Siding/Cladding Removal & Disposal Calculator
- Add one row per wall section/area being torn off, with its area and material (and gauge or coursing where relevant).
- Mark Built/Sided Before 1980 if relevant, to see the lead paint/asbestos advisory.
- Leave dumpster size on Auto for a recommendation, or manually select a size to check its adequacy.
- Turn on Cost Estimation and enter your hauler's quoted base rate, included weight allowance, and overage rate.
Practical Siding Removal Tips
- On a mixed-material job, enter each wall/material as its own row — pooling everything under one material badly skews both the weight and the recommended dumpster size.
- Break rigid materials (fiber cement, stucco chunks, veneer units) into smaller pieces as you remove them — large intact sections waste dumpster volume compared to broken, stacked pieces.
- Keep debris dry where possible — wet, water-damaged wood siding or soaked stucco debris is meaningfully heavier than the same material dry.
- Load a dumpster evenly across its floor rather than piling debris high at one end, which can make a load unsafe to transport even under the weight limit.
- If a job is close to the weight-bound tier boundary between two dumpster sizes, confirm the exact overage rate before committing — it's often cheaper to book one size up than to pay a big overage fee.
- Separate any metal (panels, flashing, fasteners) from other siding debris where your hauler offers mixed-material or recycling pricing — some haulers price clean loads lower.
Common Mistakes
- Sizing a dumpster by volume alone, then getting hit with an unexpected overage fee once the weight limit is reached first on a heavy material like stucco or brick veneer.
- Disturbing pre-1980 siding, trim, or paint without testing for lead and asbestos first.
- Treating every material as roughly the same weight per square foot — vinyl and stucco differ by nearly 20x, so a one-size-fits-all estimate is unreliable across materials.
- Assuming a hauler's advertised weight limit for a given dumpster size matches every other hauler's limit for the same nominal size.
- Forgetting that double-coursed cedar shingle/shake walls have roughly double the removal weight of a single-coursed wall of the same area.
- Not accounting for house wrap, sheathing, furring, or insulation debris removed in the same job — this calculator covers the cladding material debris only.
- Overloading a dumpster above its rim or weight limit, which many haulers will refuse to transport or will charge a significant penalty for.
Siding/Cladding Removal & Disposal Calculator Limitations
- This calculator estimates siding/cladding debris weight, volume, dumpster sizing, and disposal cost only — it does not estimate demolition labor hours, labor cost, scaffolding/lift rental, or dumpster delivery/pickup/trip fees.
- It does not test for, detect, or advise on the actual presence of lead paint or asbestos — the Built/Sided Before 1980 toggle only surfaces a general safety advisory; only a professional lab test can confirm either.
- Dumpster weight limits shown are typical, cross-checked planning figures, not a specific hauler's exact posted terms, which vary by company and region.
- The weight-per-sq-ft and bulk-density figures used for each material are published industry planning figures, not lab-measured constants for your specific debris — 4 of the 10 materials reuse this site's own install-calculator weight constants, while the other 6 are cross-checked estimates (EIFS and vinyl's bulk density carry the lowest confidence, disclosed in the Formula/FAQ sections).
- Only the cladding material debris itself is estimated — house wrap, rigid insulation, furring strips, sheathing, or other demolition debris removed in the same job is not included.
- New siding installation is not estimated here — see this category's material-specific install calculators (Vinyl, Fiber Cement Lap, Wood/Engineered Wood, Stucco, House Wrap, Brick/Stone Veneer, EIFS, Metal/Steel Panel, Cedar Shake/Shingle, Rainscreen Furring) for those.
Related Construction Calculators
You may also find these calculators useful for the same job:
- Vinyl Siding Calculator
Estimate the new siding going back on after demo.
- Fiber Cement Lap Siding Calculator
A durable replacement material for the new install.
- House Wrap Calculator
Size the new weather barrier if re-siding down to the sheathing.
- EIFS (Synthetic Stucco) Calculator
Replacing heavy traditional stucco with a lighter synthetic system.
Disclaimer: This calculator provides approximate results for planning and estimation purposes only. Actual requirements may vary based on site conditions, materials, workmanship, and local building regulations. Always consult a qualified engineer, architect, or construction professional before making final decisions.