TryBuildCalcDeck Post Spacing / Footing Calculator (Post Count & Footing Count)
Find your deck post count instantly.
🕒 Last updated: September 3, 2026
Inputs
ℹ️The bearing-to-bearing distance each joist crosses, from the house ledger to the beam — sets the joist's cut length.
ℹ️The direction joists are spaced along, parallel to the house — determines the joist count.
ℹ️Sets the joist's actual/nominal depth, used for the cantilever check — verify span adequacy separately against a current deck span guide.
ℹ️Horizontal projection of the joists past the beam, if any. Commonly limited to the joist's nominal depth (IRC R502.3.3).
ℹ️Standard stock length used to buy ledger board and blocking lumber — affects how many boards are needed after joints.
Beam
ℹ️Beam ply count and size together determine span adequacy between posts — verify against a current deck span guide, not this calculator.
Posts & Footings
ℹ️Your planned on-center post spacing along the beam — capped at a generous sanity limit only, not a structural recommendation; verify a SAFE maximum against a deck beam span guide for your beam size and joist span.
ℹ️Actual post length needed, footing/pier connection to beam bearing — not the embedment/footing depth.
Waste
ℹ️Accounts for cut-offs, damaged pieces, and layout adjustments on joists — 10% is a common estimating default.
Cost
Total Joists Needed
18
2x10, includes 10% waste
Posts / Footings
5
6x6 posts at 6 ft O.C.
Joist Geometry
Joist span (ledger to beam): 12 ft
Deck length (spacing direction): 20 ft
Cantilever past beam: 0"
Cut length: 12 ft (12 ft stock)
Joist Count
Spacing: 16" O.C.
Joists before waste: 16
Total with 10% waste: 18
Ledger Board
Length: 20 ft
Boards needed: 2 (16 ft stock)
Beam
Length: 20 ft (2-ply 2x10)
Boards needed: 4 (16 ft stock, 2 segments per ply)
Posts & Footings
Posts: 5 (6x6, 3 ft cut length)
Footings: 5 (one per post)
Mid-Span Blocking
Not included in this calculation.
Ledger Joist Hangers
One per joist at the ledger: 16 hangers
Assumptions Used
Ledger-attached deck (house ledger on one side, single beam on posts on the other) — free-standing decks are not modeled. Joist count uses the same on-center spacing formula as wall studs, rafters, and floor joists. Joist cut length is your entered span plus any cantilever, rounded up to a real stock lumber length where one covers it. The beam is assumed to run the full deck length in your selected ply count and lumber size; post count/footings use your entered post spacing directly. This calculator selects joist, beam, and post SIZE from your input but does not verify span/size structural adequacy or post spacing against a load table — confirm your selections against a current, locally-adopted deck construction guide (e.g. DCA 6) or a structural professional before framing. The joist cantilever warning reflects the commonly-cited IRC R502.3.3 rule (cantilever ≤ nominal joist depth) — verify against your locally adopted code edition. Decking surface boards, stairs, guardrails, footing depth/frost line, and fasteners are not included.
Bill of Materials
Main material: 18 pcs + recommended tools
+−
Bill of Materials
Main material: 18 pcs + recommended tools
Computed items reflect your entered span, length, and post spacing; consumables below are general recommendations — actual needs vary by product, connection method, and site conditions.
For Your Job
Deck Joists
Ledger Board
Beam
Posts
Ledger Joist Hangers
General Tools & Consumables
Ledger board flashing
Ledger lag screws / through-bolts
Deck lateral load connectors (hold-downs)
Joist hangers (treated-lumber rated)
Structural screws / hanger nails (treated-lumber rated)
Post base connectors
Post cap connectors (beam-to-post)
Concrete for footings
Framing nailer or hammer
Circular saw or miter saw
Tape measure
Post hole digger or auger
4 ft level
Safety glasses, work gloves & fall protection
Diagram simplified for clarity (not to scale)
Looking for the verification checklist, reference tables, tips, or common mistakes?See the complete Deck Framing Calculator.
Deck post & footing count
Post count follows the same on-center formula used elsewhere on this site — one post at each end of the beam plus however many more fit your chosen spacing. Each post gets one footing.
This page defaults to a 20 ft deck length with 6 ft post spacing — edit the inputs above to match your actual deck.
Deck Framing Calculator Formula: How Is It Determined?
Joist cut length, joist count, ledger board, beam, and posts/footings, calculated separately and combined into a material takeoff.
Step 1 — Joist Cut Length & Count
Cut Length = Joist Span + (Cantilever ÷ 12)
Joists (before waste) = ceil((Deck Length in inches) ÷ Spacing) + 1
Total Joists = ceil(Joists before waste × (1 + Waste Factor ÷ 100))
Cut length is your entered span plus any cantilever past the beam. Joist count uses the same on-center spacing formula as field studs, rafters, and floor joists, then rounded up after applying your waste factor.
Step 2 — Ledger Board & Beam
Ledger Length = Deck Length
Ledger Boards = ceil(Ledger Length ÷ Stock Length)
Beam Length = Deck Length
Beam Segments per Ply = ceil(Beam Length ÷ Stock Length)
Beam Boards = Beam Segments per Ply × Beam Plies
The ledger board and beam are both assumed to run the full deck length, bought in the same selected stock length as the ledger. A beam longer than one stock-length board needs more than one segment per ply, so beam board count scales with however many segments are actually needed — separately, a beam whose full length exceeds even the longest available stock (24 ft) is flagged as needing a splice directly over a post or an engineered beam, regardless of the stock length you buy in.
Step 3 — Posts & Footings
Posts = ceil(Beam Length ÷ Post Spacing) + 1
Footings = Posts (one per post)
Post count uses your entered post spacing directly — this input is capped at a generous sanity limit only, not a structural recommendation, and this calculator does not validate it against a load table. Each post gets one footing.
Worked Example
This example walks through your current inputs above, using the same steps as the Formula section.
Input Values Used
| Input | Value | Why it is used |
|---|---|---|
| Joist span / deck length | 12 ft / 20 ft | Sets cut length and joist count |
| Spacing / lumber size | 16" O.C. / 2x10 | Sets joist count and the cantilever check |
| Beam / post spacing | 2-ply 2x10 / 6 ft | Sets beam board count and post count |
Step 1 — Joist Cut Length & Count
| Calculation | Result |
|---|---|
| Cut length | 12 ft (12 ft stock) |
| Joists before waste | 16 |
| Total joists (with 10% waste) | 18 |
Step 2 — Ledger Board & Beam
| Calculation | Result |
|---|---|
| Ledger boards (16 ft stock, 20 ft length) | 2 |
| Beam boards (2-ply, 20 ft length) | 4 |
Step 3 — Posts & Footings
| Calculation | Result |
|---|---|
| Posts (6x6, 6 ft O.C.) | 5 |
| Footings (one per post) | 5 |
Therefore, this 12 ft span, 20 ft deck at 16" O.C. needs approximately 18 joists, 4 beam boards (2-ply), and 5 posts/footings.
Related Calculators
Disclaimer: This calculator provides approximate results for planning and estimation purposes only. Actual requirements may vary based on site conditions, materials, workmanship, and local building regulations. Always consult a qualified engineer, architect, or construction professional before making final decisions.