TryBuildCalcCement Bags for PCC 1:4:8 (Plain Cement Concrete Cement Estimate)
Estimate cement bags for PCC 1:4:8.
Use this PCC 1:4:8 cement bags calculator to estimate cement quantity for plain cement concrete bedding, leveling, and foundation base work.
🕒 Last updated: August 17, 2026
Inputs
ℹ️Typical values are 1.54 for concrete and PCC, and 1.33 for mortar, plaster, and screed.
Cost
For 1.000 m³ at a 1:4:8 ratio, you need approximately 3.58 bags of cement — buy 4 bags (50 kg each).
Order Summary — Theoretical vs. Order Quantity
| Theoretical | Order Quantity | |
|---|---|---|
| Cement Bags | 3.41 bags | 4 bags (whole) |
| Cement Weight | 171 kg | 179 kg |
| Cement Volume | 0.118 m³ | 0.124 m³ |
Theoretical = before wastage. Order Quantity = after your 5.0% wastage allowance, rounded up to a whole bag.
Volume & Mix Details
Wet volume: 1.000 m³
Dry volume (×1.54): 1.540 m³
Ratio used: 1:4:8
Assumptions Used
1 bag cement = 50 kg | Cement density ≈ 1440 kg/m³ | Wastage applied once to the final cement quantity, then rounded up to a whole bag.
Looking for the verification checklist, reference tables, tips, or common mistakes?See the complete Cement Bags Calculator.
Cement bags for PCC (1:4:8) work
PCC 1:4:8 is a lean concrete mix commonly used for levelling layers, bedding concrete, and foundation base preparation — a non-reinforced layer, not structural concrete.
This page preselects the PCC ratio and concrete dry volume factor for quick cement ordering estimates on blinding or levelling work.
- 1:4:8 is the leanest common PCC mix — lower cement content than 1:3:6 or 1:2:4.
- Still uses the concrete dry volume factor (1.54), not the mortar factor, since PCC contains coarse aggregate.
- For a full PCC volume + cement + sand + aggregate result, use the dedicated PCC Calculator.
Step-by-step cement bags calculation method
Cement bag calculation starts from the required work volume. The calculator then applies dry volume correction, mix ratio distribution, density conversion, and wastage allowance.
Step 1 - Enter wet work volume
Wet volume is the final required volume of concrete, mortar, plaster, screed, or PCC. This calculator accepts m³, cubic feet, cubic yards, and liters.
Step 2 - Convert wet volume to dry volume
Dry volume accounts for voids, bulking, compaction, and practical handling variation. Common factors are 1.54 for concrete and PCC, and 1.33 for mortar, plaster, and screed.
Step 3 - Apply mix ratio
The cement share is calculated from the cement part divided by total mix parts.
Step 4 - Convert cement volume to weight
Cement density is assumed as approximately 1440 kg/m³ for estimation.
Step 5 - Convert cement weight to bags
Divide cement weight by selected bag size. For purchase planning, round the final bag count upward.
Cement Bags = Cement Weight / Bag Size
Purchase Bags = Round up Cement Bags
Worked Example
This example walks through your current inputs above, using the same steps as the Formula section.
Input Values Used
| Input | Value | Why it is used |
|---|---|---|
| Work volume | 1 m³ | Sets the wet volume to convert |
| Mix ratio / dry volume factor | 1:4:8, ×1.54 | Splits dry volume into the cement share |
| Bag size / wastage | 50 kg, 5% wastage | Converts cement weight to bags and adds a buffer for site losses |
Step 1 — Volume
| Calculation | Substitution | Result |
|---|---|---|
| Wet volume | 1 m³ | 1 m³ |
| Dry volume | 1 × 1.54 | 1.54 m³ |
Step 2 — Cement Quantity
| Calculation | Substitution | Result |
|---|---|---|
| Cement volume | 1 / 13 × 1.54 | 0.118 m³ |
| Cement weight | 0.118 × 1440 | 170.58 kg |
| Cement bags (theoretical) | 170.58 / 50 | 3.41 bags |
| With 5% wastage | 3.41 × 1.05 | 3.58 bags |
Therefore, buy 4 bags of 50 kg cement — cement is normally purchased as whole bags, so the 3.58-bag theoretical figure is rounded up.
Related Calculators
Disclaimer: This calculator provides approximate results for planning and estimation purposes only. Actual requirements may vary based on site conditions, materials, workmanship, and local building regulations. Always consult a qualified engineer, architect, or construction professional before making final decisions.