TryBuildCalcWhole-House Fan Window Opening Calculator (Required Intake Area)
Find your required window opening instantly.
🕒 Last updated: September 13, 2026
Inputs
ℹ️Gross floor area of the entire house, including closets and unoccupied areas — per HVI's own sizing convention, not just conditioned living area.
ℹ️Your home's AVERAGE per-floor ceiling height (typically 8-10 ft) — NOT a multi-story home's combined/stacked height. House area already covers the full floor area across every floor, so entering a stacked height (e.g. ~18 ft for two stories) would significantly oversize the fan.
ℹ️Only "HVI Minimum" is actually sourced from HVI (Home Ventilating Institute) — its own published minimum-capacity formula. The two lower tiers are a separate, non-HVI installer convention for a quieter, slower system that sizes below HVI's stated minimum.
ℹ️Total Net Free Area of your attic's existing exhaust venting (ridge, gable, box, or turbine vents combined) — leave blank to skip this check. A whole-house fan needs substantially more attic exhaust than typical passive ventilation.
ℹ️Total screened opening area across the windows you'd typically leave open while running the fan — leave blank to skip this check.
Recommended Fan Size
7,000 CFM
Next standard size at or above the 6,600 CFM raw requirement
Raw CFM Requirement
6,600
2,200 sq ft x 3 CFM/sq ft
Sizing Inputs
House area: 2,200 sq ft
Ceiling height: 8 ft
Performance tier: HVI Minimum (3.0 CFM/sq ft) — one air change every 2 minutes
Adjusted rate: 3 CFM/sq ft
Attic Exhaust Vent NFA
Required: 9.34 sq ft
Enter your existing attic vent NFA to check sufficiency.
Window Opening
Required: 28 sq ft
Available: 10 sq ft
Short by 18 sq ft
Assumptions Used
Raw CFM requirement = house gross floor area x CFM/sq ft rate at an 8 ft ceiling. Only ONE of the three rates is actually sourced from the Home Ventilating Institute (HVI) — the industry body that certifies residential ventilation fan performance: HVI's own published minimum-capacity formula is gross sq ft x 3.0, for one full air change every 2 minutes, and that figure is this calculator's "HVI Minimum" tier and its default. The two lower rates (2.0 and 2.5 CFM/sq ft) are NOT from HVI — they come from a separate installer/retailer convention for a quieter, slower system that runs below HVI's own stated minimum, offered here as an explicit trade-off, not as an alternate "HVI-approved" option. The rate scales proportionally for ceiling heights other than 8 ft, since a taller ceiling means more air volume per sq ft of floor area. The raw requirement is rounded UP once, and that SAME rounded value is used both for display and for choosing the nominal tier, so the two can never look inconsistent with each other. Nominal fan sizes (1,200 to 10,000 CFM) reflect commonly-available commercial product tiers, not any one specific brand's lineup — a requirement above this list doesn't mean no larger single unit exists, only that it's beyond what this calculator's own reference list covers. Required attic exhaust vent Net Free Area (NFA) and required window opening are both rounded UP (never to-nearest) before the sufficiency check, so a value exactly matching the displayed figure is never incorrectly marked sufficient against a slightly larger true requirement. NFA uses DOE/HVI-aligned guidance of 1 sq ft of NFA per 750 CFM of fan capacity — some installers cite a more conservative 1:500 ratio instead. Window opening uses DOE/PNNL guidance of 4 sq ft of screened opening per 1,000 CFM. Both the vent and window requirements are sized to the fan size you'd actually buy (the nominal tier), not the smaller raw theoretical minimum. This calculator is a planning estimate only — it does not verify structural ceiling-joist bay clearance, wiring/switch requirements, or local code compliance for the fan installation itself.
Looking for the verification checklist, reference tables, tips, or common mistakes?See the complete Whole-House Fan Calculator.
Window opening area for a whole-house fan
A whole-house fan needs a real supply air path — at least 4 sq ft of screened window opening per 1,000 CFM of fan airflow, per DOE/PNNL guidance.
This page defaults to a 2,200 sq ft home at the HVI Minimum tier with 10 sq ft of available window opening entered — edit the inputs above to check your own home's sufficiency.
Whole-House Fan Calculator Formula: How Is It Determined?
Required CFM is determined by house area, ceiling height, and desired cooling performance, then converted into a real fan size, required attic exhaust NFA, and required window opening.
Step 1 — Adjusted CFM Rate
Adjusted CFM/sq ft = Tier Rate x (Ceiling Height / 8 ft)
Tier rate is 2.0 (Reduced Airflow), 2.5 (Moderate Airflow), or 3.0 (HVI Minimum, the default) CFM per sq ft, all defined at the standard 8 ft ceiling this rule of thumb assumes. Only the 3.0 rate is actually HVI's own published minimum-capacity formula (one full air change every 2 minutes) — the two lower rates are a separate installer/retailer convention for a quieter, slower system that runs below HVI's stated minimum, not an alternate "HVI-approved" option. A taller ceiling scales the rate up proportionally, since it represents more air volume per sq ft of floor area.
Step 2 — Raw CFM & Nominal Fan Size
Raw CFM = ceil(House Area sq ft x Adjusted CFM/sq ft)
Nominal Fan Size = smallest commercially-available CFM tier >= Raw CFM
The raw requirement is rounded UP once (never down, since this is a minimum), and that SAME rounded value is used both for display and for choosing the nominal tier — so the two can never look inconsistent with each other. If the raw requirement exceeds every tier on this calculator's own reference list (1,200-10,000 CFM), it's flagged as "Above Listed Nominal Range" — meaning beyond this calculator's own list, not that no larger single commercial unit exists in the real market.
Step 3 — Attic Exhaust Vent NFA & Window Opening
Required Attic Vent NFA (sq ft) = ceil-to-hundredth(Sizing-Basis CFM / 750)
Required Window Opening (sq ft) = ceil-to-hundredth((Sizing-Basis CFM / 1,000) x 4)
Both requirements are sized to the fan you'd actually buy (the nominal tier), not the smaller raw theoretical minimum, and rounded UP (never to-nearest) so a value exactly matching the displayed figure is never incorrectly marked sufficient against a slightly larger true requirement. Attic vent NFA uses DOE/HVI-aligned guidance of 1 sq ft of NFA per 750 CFM. Window opening uses DOE/PNNL guidance of 4 sq ft of screened opening per 1,000 CFM. If you enter your existing attic vent NFA or available window opening, this calculator flags whether each is sufficient.
Worked Example
This example walks through your current inputs above, using the same steps as the Formula section.
Input Values Used
| Input | Value |
|---|---|
| House area | 2,200 sq ft |
| Ceiling height | 8 ft |
| Performance tier | HVI Minimum (3.0 CFM/sq ft) — one air change every 2 minutes |
Step 1 — Adjusted CFM Rate
| Calculation | Result |
|---|---|
| Adjusted rate = 3 x (8 / 8) | 3 CFM/sq ft |
Step 2 — Raw CFM & Nominal Fan Size
| Calculation | Result |
|---|---|
| Raw CFM = ceil(2,200 x 3) | 6,600 CFM |
| Nominal fan size | 7,000 CFM |
Step 3 — Attic Exhaust Vent NFA & Window Opening
| Calculation | Result |
|---|---|
| Attic vent NFA = 7,000 / 750 | 9.34 sq ft |
| Window opening = (7,000 / 1,000) x 4 | 28 sq ft |
Therefore, a 2,200 sq ft home at the HVI Minimum tier needs approximately a 7,000 CFM whole-house fan, 9.34 sq ft of attic exhaust vent NFA, and 28 sq ft of open window area. Verify your chosen fan is HVI-916 certified before purchasing.
Disclaimer: This calculator provides approximate results for planning and estimation purposes only. Actual requirements may vary based on site conditions, materials, workmanship, and local building regulations. Always consult a qualified engineer, architect, or construction professional before making final decisions.