TryBuildCalcHeat Pump SEER Savings Calculator (Cooling Season Only)
Estimate your heat pump's cooling-season savings instantly.
🕒 Last updated: September 18, 2026
Inputs
ℹ️Same capacity assumed for both the old and new unit — this isolates the efficiency difference as the only variable.
ℹ️Prefills a typical annual cooling hours estimate below — edit that field directly if you know your actual usage.
ℹ️A smart thermostat's own runtime log (if available) is more accurate than this climate-zone default.
ℹ️Use your summer/peak-season rate if your utility has time-of-use pricing, for the most realistic cooling-season estimate.
Current (Old) System
ℹ️Most units installed before 2023 carry a SEER rating, not SEER2.
ℹ️From the nameplate or an AHRI Directory lookup by model number, not guessed from the unit's age.
New / Replacement System
ℹ️Virtually every unit sold since 2023 carries a SEER2 rating.
ℹ️From the specific quoted model's spec sheet, for the exact indoor/outdoor combination being installed.
ℹ️Enter your NET cost after any rebates/tax credits to unlock a simple payback period below.
Estimated Annual Savings
$107
19% less cooling energy use per year
Current (Old) System
Entered rating: 14 SEER
SEER2-equivalent: 13.4
Annual energy use: 3,769 kWh
Annual cost: $565
New / Replacement System
Entered rating: 16.5 SEER2
SEER2-equivalent: 16.5
Annual energy use: 3,055 kWh
Annual cost: $458
Cumulative Savings Over Time
Year 1
$107
Year 5
$535
Year 10
$1,070
Year 15
$1,605
Year 20
$2,140
Assumptions Used
Annual kWh = (Tonnage × 12,000 BTU/ton ÷ SEER2-equivalent rating) × Annual Cooling Hours ÷ 1000, computed once for each unit and multiplied by your electricity rate. A rating entered as SEER (pre-2023) is normalized to an approximate SEER2-equivalent by dividing by 1.047 before this formula runs — DOE's 2023 M1 test procedure reads roughly 4.5-5% lower than the old SEER test for identical equipment, though the real difference varies by equipment type (variable-speed ~3-4%, single-speed ~5-6%), so this is a published approximation, not an exact per-unit conversion. Annual cooling hours default from your selected climate zone as a broad planning estimate — no single authoritative national table exists, so your own smart-thermostat runtime log (if available) is more accurate than this default. The payback period (when shown) is simply net installed cost ÷ annual savings, and the cumulative savings table assumes a flat electricity rate with no future inflation, financing costs, or maintenance-cost differences between the two units — this is a planning estimate, not a full financial analysis.
Looking for the verification checklist, reference tables, tips, or common mistakes?See the complete SEER Savings Calculator.
Heat pump cooling-season SEER savings
Heat pumps use the same SEER/SEER2 rating system for cooling as central air conditioners — this page estimates only the cooling-season savings from a heat pump replacement, since heating-season savings depend on a separate HSPF/HSPF2 rating this calculator doesn't model.
This page defaults to a 3.5-ton heat pump in a cool climate zone — edit the inputs above to match your actual system.
SEER Savings Formula: How Is It Determined?
The same formula runs once for each unit, using each unit's normalized SEER2-equivalent rating, then the two results are compared.
SEER-to-SEER2 Normalization
If rating type is SEER2: SEER2-equivalent = entered value (no change)
If rating type is SEER: SEER2-equivalent = entered value ÷ 1.047
DOE's 2023 M1 test procedure for SEER2 uses much higher external static pressure than the old SEER test, so identical equipment reads a lower SEER2 number. 1.047is a commonly-cited approximate conversion factor — the real difference varies by equipment type (variable-speed/ECM systems see a smaller ~3-4% drop, single-speed/PSC systems a larger ~5-6% drop), so treat this as a planning approximation, not an exact per-unit figure. If you have a unit's actual AHRI-certified SEER2 rating, use that directly instead.
Annual Energy Use and Cost
Annual kWh = (Tonnage × 12,000 BTU/ton ÷ SEER2-equivalent) × Annual Cooling Hours ÷ 1000
Annual Cost = Annual kWh × Electricity Rate
This runs once using the old unit's normalized SEER2-equivalent and once using the new unit's — both assuming the SAME tonnage and cooling hours, so the only variable being measured is the efficiency-rating difference.
Annual Savings and Percent Reduction
Annual Savings = Old Unit Annual Cost − New Unit Annual Cost
Percent Energy Reduction = (Old Annual kWh − New Annual kWh) ÷ Old Annual kWh × 100
A negative annual savings figure means the "new" unit is actually less efficient than the "old" one once both are normalized — this calculator reports that honestly rather than hiding it.
Payback Period (Optional) and Cumulative Savings
Simple Payback Period = New System Installed Cost ÷ Annual Savings
Cumulative Savings (Year N) = Annual Savings × N
Payback period only appears when an installed cost is entered and savings are positive (and the payback period is under 100 years). The cumulative savings table assumes a flat electricity rate over time, with no adjustment for future rate inflation, financing costs, or maintenance-cost differences between the two units.
Worked Example
This example walks through your current inputs above, using the same steps as the Formula section.
Input Values Used
| Input | Value |
|---|---|
| Cooling capacity / climate zone | 3.5 tons / Zone 5 — Cool (Midwest, PA, OH, CO) |
| Annual cooling hours / rate | 1200 hrs / $0.15/kWh |
| Old unit rating | 14 SEER (pre-2023 rating) |
| New unit rating | 16.5 SEER2 (2023+ DOE rating) |
Step-by-Step Calculation
| Step | Calculation | Result |
|---|---|---|
| Old unit SEER2-equivalent | 14 ÷ 1.047 | 13.4 |
| New unit SEER2-equivalent | 16.5 (already SEER2) | 16.5 |
| Old unit annual kWh | (3.5 × 12,000 ÷ 13.4) × 1200 ÷ 1000 | 3,769 kWh |
| New unit annual kWh | (3.5 × 12,000 ÷ 16.5) × 1200 ÷ 1000 | 3,055 kWh |
| Old / New annual cost | kWh × $0.15 | $565 / $458 |
| Annual savings | $565 − $458 | $107 |
Therefore, replacing this 3.5-ton system rated 14 SEER (pre-2023 rating) with a new one rated 16.5 SEER2 (2023+ DOE rating) saves an estimated $107 per year (19% less cooling energy).
Disclaimer: This calculator provides approximate results for planning and estimation purposes only. Actual requirements may vary based on site conditions, materials, workmanship, and local building regulations. Always consult a qualified engineer, architect, or construction professional before making final decisions.