TryBuildCalcKitchen Plumbing Pipe Sizing Calculator (Kitchen & Utility Branch Sizing)
Size the water supply pipe for a kitchen and utility branch.
🕒 Last updated: July 31, 2026
Building & System Type
ℹ️Sets which WSFU value applies to each fixture — the same fixture carries a different load in a single home versus an apartment building versus a commercial building.
ℹ️Flushometer-valve systems demand much more flow at the same fixture-unit count than flush-tank systems — select whichever matches most of the water closets/urinals on this pipe segment.
Fixtures
Quick-fill a starting point, then add/remove/edit rows as needed:
Fixture 1
Fixture 2
Fixture 3
Only fixtures listed for the selected Building/Occupancy Type are shown — up to 30 fixture rows total.
Continuous-Flow Fixtures (Optional)
Hose bibbs and lawn sprinkler zones are continuous-use, not intermittent — per IPC Appendix E they're added directly in GPM here, not as fixture units above.
Continuous-Flow Fixture 1
Pipe Sizing
ℹ️Sets which standard nominal sizes and internal diameters the recommended size is rounded up to.
ℹ️Defaults to 8 ft/s for cold water branches — commonly lowered to around 5 ft/s for hot water piping.
🔧 Recommended pipe size: 3/4" CPVC (CTS, SDR11)
Total load: 5.1 WSFU → estimated demand 9.55 GPM.
Fixture Unit Load
Kitchen Sink (x1): 1.1 WSFU
Dishwasher (x1): 1 WSFU
Clothes Washer (x1): 3 WSFU
Demand Estimate
Building/Occupancy Type: Individual Dwelling Unit
System Type: Predominantly Flush-Tank Fixtures
Total Fixture Units (WSFU): 5.1
Fixture-Unit Demand: 4.55 GPM
Continuous-Flow Demand: 5 GPM
Hose bibbs/sprinklers — added directly, not run through the fixture-unit curve
Total Estimated Demand: 9.55 GPM
0.6 L/s, 2.17 m³/hr
Continuous-Flow Fixtures
Hose bibbs and sprinkler zones are added directly in GPM, not converted to fixture units — see Design Notes below.
Hose Bibb / Garden Hose Connection (x1 @ 5 GPM each): 5 GPM
Pipe Sizing
Pipe Material: CPVC (CTS, SDR11)
Maximum Velocity: 8 ft/s
Required Minimum Internal Diameter: 0.698 in (17.7 mm)
Recommended Nominal Pipe Size: 3/4"
Actual ID 0.716 in (18.2 mm) — velocity at this size: 7.61 ft/s
Design Notes
This is a velocity-limited quick-sizing estimate, not a full hydraulic pressure-loss design. For anything beyond routine residential/light-commercial branch sizing, confirm with a full IPC Appendix E / UPC Table 610.3 pressure-loss calculation accounting for developed length, fittings, elevation change, and available pressure.
Hose bibbs and sprinkler zones are continuous-flow demand, not fixture units — per IPC Appendix E they are excluded from the fixture-unit/demand-curve method and added directly in GPM on top of it.
Approximate results for planning only. Verify with a professional.
Looking for the verification checklist, reference tables, or tips and mistakes?See the complete Pipe Sizing by Fixture Units Calculator.
Kitchen and utility branch sizing estimate
This page is set up for a kitchen/utility branch — a kitchen sink, dishwasher, and clothes washer — giving 5.1 total WSFU (1.1 + 1.0 + 3.0), which interpolates to an estimated 4.55 GPM fixture-unit demand on the flush-tank curve. The clothes washer is the single largest WSFU contributor on this branch despite being a utility appliance, not a kitchen fixture itself.
The branch also feeds one exterior hose bibb. Per IPC Appendix E, a hose bibb is a continuous-flow connection, not a fixture unit — it's added directly as 5 GPM on top of the fixture-unit demand, giving a total of 9.55 GPM. At 8 ft/s in CPVC (CTS, SDR11), that needs a 0.698 in minimum diameter, rounding up to a 3/4" nominal size (actual ID 0.716 in, actual velocity 7.61 ft/s).
- 3 fixtures → 5.1 WSFU → 4.55 GPM fixture-unit demand.
- + 1 hose bibb (continuous-flow) → +5 GPM → 9.55 GPM total demand.
- Recommended: 3/4" CPVC/CTS (actual velocity 7.61 ft/s).
How Pipe Sizing by Fixture Units Works
The calculation happens in four stages — fixture-unit load, demand flow rate, an optional continuous-flow addition, then pipe diameter.
Step 1 — Total Fixture Unit Load
Total WSFU = Sum of every fixture row's WSFU
Each fixture's WSFU value depends on the selected Building/Occupancy Type — the same fixture is rated lower in a multi-family building than a single-family home, reflecting greater usage diversity across more dwelling units sharing the same riser.
Step 2 — Demand Flow Rate (GPM)
This relationship is deliberately nonlinear — doubling the fixture-unit total does not double the demand flow rate, since the probability of every fixture running simultaneously keeps dropping as the count grows. Flushometer-valve systems draw a much higher flow at the same WSFU total than flush-tank systems, since a flush valve delivers its full flush volume quickly with no tank to buffer the draw.
Step 3 — Add Continuous-Flow Demand (Optional)
Hose bibbs, lawn sprinkler zones, and similar continuous-use connections are excluded from the fixture-unit method entirely — per IPC Appendix E, fixture units and the demand curve model intermittent, probability-of-simultaneous-use demand, which doesn't apply to a fixture that can run continuously for an extended period. Their GPM is instead added directly on top of the fixture-unit-derived demand (IPC's own worked example: 2 hose bibbs × 5 GPM = 10 GPM, added to the WSFU-derived total).
Step 4 — Required Pipe Diameter
Recommended Nominal Size = smallest standard size for the chosen material whose actual ID ≥ Required Minimum ID
0.4085 comes directly from converting GPM to cubic feet per second and expressing pipe area from a diameter in inches — this is a standard plumbing/HVAC flow-velocity relationship. Since pipe only comes in discrete standard sizes, the required diameter is always rounded up, never down, and the actual velocity at the recommended size (shown in the result) will sit at or below your chosen maximum.
Worked Example
This example uses the active inputs above and follows the same steps as the Formula section.
Input Values Used
| Input | Value |
|---|---|
| Fixtures | Kitchen Sink x1, Dishwasher x1, Clothes Washer x1 |
| Continuous-Flow Fixtures | Hose Bibb / Garden Hose Connection x1 @ 5 GPM |
| Building Type / System Type | individualDwelling, flushTank |
| Pipe Material / Max Velocity | CPVC (CTS, SDR11), 8 ft/s |
Step 1 — Fixture Unit Load
| Fixture | Substitution | Result |
|---|---|---|
| Kitchen Sink | 1.1 × 1 | 1.1 WSFU |
| Dishwasher | 1 × 1 | 1 WSFU |
| Clothes Washer | 3 × 1 | 3 WSFU |
| Total WSFU | 5.1 | |
Step 2 — Demand Flow Rate
| Calculation | Substitution | Result |
|---|---|---|
| Fixture-Unit Demand | Table lookup at 5.1 WSFU (flush-tank curve) | 4.55 GPM |
Step 3 — Continuous-Flow Demand
| Calculation | Substitution | Result |
|---|---|---|
| Hose Bibb / Garden Hose Connection | 5 GPM × 1 | 5 GPM |
| Total Demand (Fixture-Unit + Continuous-Flow) | 4.55 + 5 = 9.55 GPM | |
Step 4 — Required & Recommended Pipe Size
| Calculation | Substitution | Result |
|---|---|---|
| Required minimum ID | √(0.4085 × 9.55 ÷ 8) | 0.698 in |
| Recommended nominal size | Smallest CPVC (CTS, SDR11) size ≥ 0.698 in | 3/4" (actual velocity 7.61 ft/s) |
Therefore, this 5.1 WSFU load plus 5 GPM of continuous-flow demand needs approximately 9.55 GPM total, sized to 3/4" CPVC (CTS, SDR11).
This does not include developed pipe length, fittings, elevation, or available service pressure. Cross-check against the Reference Tables in the complete Pipe Sizing by Fixture Units Calculator.
This page keeps things focused on the calculation above. For the full construction guide — verification checklist, reference tables, usage steps, tips, common mistakes, and limitations.See the complete Pipe Sizing by Fixture Units Calculator.