TryBuildCalcAAC Block Calculator 600x200x100(100 mm AAC Partition Block Estimate)
Calculate 600 x 200 x 100 mm AAC blocks.
Use this 600 x 200 x 100 mm AAC block calculator to estimate partition wall block quantity with mortar joint thickness and wastage allowance.
🕒 Last updated: August 21, 2026
Inputs
ℹ️AAC blocks are laid with thin-bed adhesive, typically 2-3 mm — not conventional mortar.
Cost
Theoretical Blocks
76 blocks
Wall Area: 9.29 m²
Wall Volume: 0.929 m³
Blocks per m²: 8.2
Thickness: 100 mm
Recommended Blocks
(Including 5% Wastage)
80 blocks
Wastage: 4 blocks
Mortar: 0.02 m³
AAC partition block calculation for 600 x 200 x 100 mm size
The 600 x 200 x 100 mm AAC block is commonly used for thinner partition walls where a 100 mm wall thickness is suitable.
This page preselects the 100 mm AAC block so you can quickly estimate the number of partition wall blocks required for a given wall length and height.
- Block length: 600 mm.
- Block height: 200 mm.
- Typical partition wall thickness: 100 mm.
How does this block calculator work?
Block quantity is calculated using wall dimensions and effective block size including mortar joints.
Step 1 — Wall Area
Step 2 — Effective Block Size
Effective Length = Block Length + Mortar Thickness
Effective Height = Block Height + Mortar Thickness
Step 3 — Calculate Theoretical Blocks
Step 4 — Add Wastage Allowance
Wastage Blocks = round up(Theoretical Blocks × Wastage %)
Adjusted (Recommended) Blocks = Theoretical Blocks + Wastage Blocks
Both the theoretical count and the wastage allowance are rounded up separately to whole blocks, since blocks can only be purchased as whole units. Because of this two-step rounding, the final recommended quantity can differ slightly from simply multiplying the unrounded total by (1 + Wastage %).
Real-World Block Calculation Example
This example uses the active calculator inputs and explains the complete calculation method step by step. Each table shows the formula, values placed into the formula, and the final result.
Input Values Used
| Input | Value | Purpose |
|---|---|---|
| Wall Length | 10 ft | Site wall length |
| Wall Height | 10 ft | Site wall height |
| Block Type | AAC Block 600 x 200 x 100 mm | Determines block face size and wall thickness |
| Mortar Joint Thickness | 3 mm | Added to block length and height for the effective block area |
| Wastage Allowance | 5% | Added on top of the theoretical block count |
Step 1 — Calculate Wall Area
| Wall area | 10 ft × 10 ft | 9.29 m² |
Step 2 — Calculate Effective Block Area
| Calculation | Formula / Substitution | Result |
|---|---|---|
| Effective block length | 600 + 3 mm | 603 mm |
| Effective block height | 200 + 3 mm | 203 mm |
| Effective block area | Effective length × Effective height, converted to m² | 0.1224 m² |
Step 3 — Calculate Theoretical Blocks
| Theoretical blocks | round up(9.29 m² ÷ 0.1224 m²) | 76 blocks |
Step 4 — Add Wastage Allowance
| Wastage blocks | round up(76 × 5%) | 4 blocks |
| Recommended blocks | 76 + 4 | 80 blocks |
Therefore, for this input, you need approximately 76 blocks (theoretical), or 80 blocks including a 5% wastage allowance — approximately 8.2 blocks/m² of wall face, plus an estimated 0.02 m³ of mortar/adhesive.
Practical Ordering Note
Block count depends on the face size (length × height) of the block, not its width — a thinner or thicker block of the same face size needs the same number of units, just a different wall thickness and mortar volume. This estimate also does not deduct door and window openings — subtract their area separately for a tighter order quantity.
Limitations of block estimation
This calculator assumes a simple rectangular wall and does not account for openings such as doors and windows. Actual block requirements may vary depending on site conditions and construction practices.
Related Calculators
Disclaimer: This calculator provides approximate results for planning and estimation purposes only. Actual requirements may vary based on site conditions, materials, workmanship, and local building regulations. Always consult a qualified engineer, architect, or construction professional before making final decisions.